SINOCMP 101-1007-009 101-1555 101-1007 Hydraulic Motor Replacement for Char-Lynn Eaton H Series, 17.9 cu in/rev Displacement, 1 Inch Straight Shaft 4-Bolt Mount 192 RPM 1350 PSI

Restore Reliable Power With This 101-1007-009 H Series Hydraulic MotorSlow brush rotation, weak auger torque, and unexpected breakdowns often point to a worn hydraulic motor. This replacement hydraulic motor 101-1007-009 brings Char-Lynn Eaton H Series equipment back to original performance.Critical Dimensions ChecklistPilot diameter: 3.25 inch (82.55 mm) – centers motor on equipment frameMounting pattern: 4-bolt on 3.25 inch bolt circle – standard H Series configurationMounting bolts: 3/8-16 UNC-2B thread sizeShaft: 1 inch straight with Woodruff key slot, 1/4-20 UNC-2B threaded end holePorts: 1/2-14 NPTF dryseal thread – side port locationDisplacement: 17.9 cu in/rev (294 cc/rev) – produces 192 RPM at 15 GPM flowStep-by-Step Installation Guide🔹 Before touching any lines, shut down the hydraulic power unit and cycle control valves to release stored pressure.🔹 Clean the area around the existing motor. Dirt entering open ports is the fastest way to damage a gerotor spool valve.🔹 Label each hose before disconnecting. Note which port receives pressure flow for correct rotation direction.🔹 Measure your old motor's pilot diameter and bolt pattern. This 101-1007-009 hydraulic motor fits H Series mounts with 3.25 inch pilot and 4-bolt pattern on 3.25 inch circle.🔹 Install the Woodruff key into the shaft keyway before attaching the driven component.🔹 Mount this H series hydraulic motor using four 3/8-16 bolts. Tighten in a crossing pattern to 30-40 ft-lbs.🔹 Connect pressure and return lines to the 1/2 NPTF dryseal side ports. Thread by hand first to avoid cross-threading, then tighten with a wrench. Do not exceed 30 ft-lbs torque on NPTF fittings.🔹 To reverse rotation direction, swap the two hose connections. This 101-1007-009 replacement hydraulic motor operates smoothly in either direction.🔹 Before final connection to this hydraulic motor, flush supply lines by running clean fluid into a bucket. Debris from old motors destroys gerotor components.🔹 Start the system at reduced flow. Run for two minutes at low speed. Check all port connections for leaks. Gradually increase to operating flow while monitoring for unusual noise.Operating Guidelines and Limitations⚠️ Maximum continuous pressure is 1350 PSI. Brief intermittent operation up to 1800 PSI is permitted for no more than 10% of each minute.⚠️ Maximum operating temperature is 180°F. Higher temperatures degrade seal materials and reduce motor life.⚠️ Maximum continuous flow is 15 GPM. Intermittent flow up to 20 GPM is allowed for short durations only.⚠️ Do not operate with equal pressure at both ports. Maintain at least 50 PSI differential between inlet and outlet.⚠️ Use premium anti-wear hydraulic oil. Maintain filtration per ISO 4406 cleanliness code 20/18/13.⚠️ Avoid thermal shock. Do not introduce fluid more than 70°F above or below motor casing temperature.Order With ConfidenceDowntime costs money. Keep a spare 101-1007-009 hydraulic motor on your service truck or in your parts room. Click add to cart now and restore your equipment's low-speed torque.

• [🔧] Direct Swap for 101-1007 Models: Hydraulic motor directly replaces Eaton Char-Lynn part numbers 101-1007-009, 1011007009, 101-1007, 1011007, 101-1555, and 1011555, ensuring proper fitment for H Series hydraulic systems.
• [⚙️] High Torque at Low Speed: With 294 cm³/r (17.9 in³/r) displacement, this H Series motor delivers substantial torque output (400 Nm max) for demanding applications requiring constant speed variations with slow or quick rotary movement.
• [🛢️] Simple NPTF Dryseal Plumbing: This Char-Lynn style hydraulic motor features 1/2-14 NPTF side ports for easy hose connection. The NPTF dryseal threads on this 101-1007-009 replacement hydraulic motor create reliable seals without additional sealant, saving installation time on car washes and industrial equipment.
• [🏗️] Three Moving Parts Reliability: Only three internal components rotate inside this H series hydraulic motor. The simple gerotor-star, drive, and shaft design makes this 101-1007-009 hydraulic motor easier to maintain and less likely to fail than complex multi-piston alternatives. Maximum intermittent pressure reaches 1800 PSI for short durations.
• [📦] 1-Inch Shaft with Woodruff Key: Equipped with 1 inch diameter shaft featuring Woodruff key and 1/4-20 UNC-2B threaded hole in shaft end for positive torque transmission and secure component attachment.